A Level Physics Paper 5 – Planning, Analysis and Evaluation

Paper 5 is a written paper to test the practical skills that you acquired during your Cambridge International A Level course.

Question 1: [Planning – 15 marks]

This question of paper 5 tests your ability to plan experiments. If you have done a good amount of practical work during your A Levels, this question won’t be much of a concern for you (especially if you paid good attention to your paper 3 of Physics). Whatever you practically perform in your paper 3, you have to write it in this paper.

While solving this question, keep these pointers in mind:

  • Defining the problem [3 marks]
  • Methods of data collection [4 marks]
  • Setup for the apparatus [1 mark]
  • Method of Analysis [2 marks]
  • Safety considerations [1 mark]
  • Any additional details [4 marks]

We’ll now describe these pointers one by one. The experiment described in this paper 5, question 1 : (May/June 2018 Paper 5 Variant 2) is used as an example for an explanation of the above pointers in the sections that follow.

Defining the problem:

Here you are required to identify the variables in the experiment:

  • Independent variable: it is a variable whose variation does not depend on that of another.
  • Dependent variable: it is a variable whose value depends on that of another.

In simpler terms, the independent variable is the variable you are going to vary in the experiment, and the dependent variable is the variable you are going to measure in the experiment (pay attention to the words ‘vary’ and ‘measure’).

After the identification of variables, you are required to identify the quantities you are going to keep constant. Any quantity which may vary your results, other than quantities involved in the experiment, must be kept constant. Mention ‘how’ you are going to make sure it does not change, and ‘why’ you think it should be kept constant. While you do this, keep in mind one thing that there may be a lot of such quantities that need to be kept constant; always mention that quantity which DIRECTLY affects the variables being measured.

Methods of data collection:

Now that you have mentioned the variables, you need to describe how to measure them. Describe the method to vary the independent variable, and a method to measure the effect on the dependent variable. State all instruments used.

In the example question, two variables are involved in the experiment, λ (independent) and h (dependent). λ can be varied by using different colored LEDs/lasers (red, green, blue, etc) and using the values for λ given on these LEDs/lasers for any calculations/analysis. The corresponding values of ‘h’ can be measured using a meter rule/plastic ruler.

As you can see now, I described above ‘HOW’ I am going to vary the independent variable, and ‘HOW’ I am going to measure the dependent variable. I also stated all the instruments used too. Along with all this, you are also required to mention the SETUP (discussed below) for the experiment; for instance, how you are going to place the LEDs/lasers (any appropriate method to support the light source, like clamping the light source using a retort stand, etc.), how you are going to place the ruler (placing the ruler close to the maxima on the screen).

You also need to describe how any errors possible may be prevented; these points you mention are counted as additional details.

Also include details on how you are going to keep constant quantities you mentioned before constant (In the example experiment described above, the constant quantity was the angle of the incident light. It can be kept constant by holding the light source using a retort stand, and not changing its position the entire experiment)

In some cases, there are no proper instruments available for the measurement of dependent quantity. For example, resistance cannot be measured using a conventional piece of apparatus directly. So for that purpose, mention all the measurements you need to take for its calculation and the instruments used (ammeter used for measurement of current, voltmeter used for measurement of p.d. across the resistor. R is then calculated using the equation: R = V/I).

Setup for the apparatus:

Draw a diagram with all the equipment you mentioned / might use during the experiment. A basic, well-labeled diagram could score many marks; even if the explanation is weak! Therefore, don’t think that the diagram is of little importance.

Method of analysis:

In all papers, an equation is given which you need to test or experiment about. Algebraically manipulate the given equation to form a linear relationship (Y = mX + c) – choose what quantity should be on each axis to give a straight line graph.

Relationship Linear form Graph Gradient y-intercept
y = mx + c y = mx + c y against x m c
y = axn g y = (n)lgx + lg a lg y against lg x n lg a
y = aekx ln y = kx + ln a ln y against x k ln a

Once you are done algebraically manipulation the equation into a linear form, describe what the graph will look like if the given relationship is true, e.g.

Relationship given is : y = axn ; linear form : lg y = (n) lgx + lg a

The graph will be linear if lg y is plotted against lg x.

Also mention, where the line will intersect the y-axix, and what will the gradient of the plotted relationship.

If quantities are asked to calculated, as in the example question given above, that can be done as follows:

The equation given in the example question is:

h = n λ/d + B

Converting this linear form; (y = mx + c) form, we get:

(the given equation is already in the linear form, so I’m just making it look like one by the use of brackets)

h = n/d (λ) + B

h is plotted on the y-axis against λ on the x-axis.

By comparing it with linear form, we know that, n/d = m = gradient, and B = c = y-intercept.

Therefore,

d = n/gradient

and

B = y-intercept

These all steps of conversion to linear form, graphical form, gradient, y-intercept, and calculation of quantities come under ‘Analysis of Data’.

Safety considerations:

Any hazards/harms involved while performing the experiment go here; for every hazard/harm, mention a way to avoid it.

For the example question, the safety precautions needed are:

  • Looking directly at the bright light source may damage your eyes [safety precaution: wear goggles, do not look directly, safety screens, etc.]

Other common safety issues for other experiments may be:

  • In electricity experiments, electrocution may occur [safety precaution: wear gloves]
  • If heating is involved, burns may occur; fire [safety precaution: wear gloves, use holders for picking up hot objects; turn off heating instruments between taking measurements]
  • For experiments involving heavy objects, moving objects, they may fall on your foot if slipped from bench/table, sand bucket for falling masses or moving objects may hit you, resulting in eye injuries or other face injuries [make sure heavy objects not placed near edges, supports are strong, wear goggles to prevent moving objects hitting your eyes]

There may be many more such harms possible, and many more precautions necessary depending on the experiment.

Additional details:

All the improvements possible, preventions of errors, etc. come under this heading.

Make yourself acquainted with the following list of apparatus (these apparatus/additional details are taken from Znotes – https://znotes.org/cie-a2-physics-9702/)

General Experiments Apparatus:

  • Signal generator: can be used to produce a sound/voltage/current and can vary frequency settings on the device
  • Micrometer: can be used to measure small distances
  • Vernier calipers: can be used to measure small distances
  • Set square: used to make sure apparatus perpendicular
  • Magnets: can be used with metal objects in the experiment
  • Balance: can be used to weigh a mass
  • Burette: accurately measuring the volume of liquid
  • Diffraction grating: can be used to measure the wavelength of a monochromatic light source

Additional Details:

  • Measuring amplitude and period using a c.r.o
    • Adjust time-base and 𝑦-gain to achieve a suitable waveform
    • Calculate amplitude by finding height in terms of boxes on a grid of waveform and multiplying by 𝑦-gain
    • Calculate period by counting boxes of grid occupied by a full waveform and multiply by time-base setting
  • Measuring diameter: repeat measurements in different positions and average
  • Wear safety goggles/use a safety screen to protect eyes when heating/pouring liquids or handling stretched wire
  • Ensure apparatus stable & not easily knocked over by placing weights (e.g. on retort stand) and working on a flat surface
  • Use a sand tray under heavyweights and make sure weights don’t fall on your foot
  • Keep radioactive substances in a lead-lined container
  • To ensure the surface is horizontal, use a spirit level
  • Sound experiment: perform the experiment in a quiet room
  • Light experiment: perform the experiment in a dark room
  • Repeat experiment & determine the average

Pressure Experiments Apparatus:

  • U-Tube (manometer): measures pressure difference between two fluids
  • Bourdon gauge: measuring the pressure of a gas or liquid
  • Pump: can be used to alter the pressure in a container

Electrical Experiments Apparatus:

  • Variable resistor (rheostat): can be used to alter voltage/current supplied in a circuit or can be used to keep current constant
  • LDR: resistance decreases with increasing light intensity
  • Photocell: sensors that allow you to detect light – generate an e.m.f when light is incident

Additional Details:

  • Use a protective resistor to reduce current
  • Switch off currents when not in use so that wires/coil do not overheat
  • Use microammeter and galvanometer for small voltages and currents
  • When using an ammeter and voltmeter to measure resistance, a power supply is required
  • Type of current to use:
    • Large current to create a large magnetic field
    • Large current to produce measurable e.m.f./voltage
    • Small current to reduce the heating effect

Magnetic Field Experiments:

  • Hall probe: used to measure magnetic fields
  • Keep Hall probe at right angles (perpendicular) to the magnetic field by fixing to rule
  • Calibrate Hall probe in a known magnetic field
  • Repeat experiment with Hall probe reversed and average
  • In magnetic experiments, avoid external alternating magnetic fields

Falling Bodies & Oscillations Experiments

  • Measuring velocity using light gate:
    • Measure distance between light gates
    • Connect light gates to time loggers
    • Calculate the time of fall by using data from loggers – time difference between when the first and second beam is broken
  • For experiments with light weights or wind, close windows & switch off the air conditioning to avoid draughts
  • For measuring the time period of oscillations, find time for 10 oscillations and then divide
  • Use fiducial markers to time oscillating objects
  • To measure quantities in an experiment with fast motions, record the experiment with a video camera and playback in slow motion
  • In an experiment with an object being dropped, make sure the object released with no/constant velocity. Can use electromagnets or a spring-loaded device
  • For falling objects, use a guide to keep motion in the correct direction

An example question 1 solved is provided at the following link:

https://www.gceguide.com/resources/notes/physics-9702/a-level-physics-paper-5-planning-analysis-and-evaluation/level-physics-paper-5-octobernovember-2008-solved/

Question 2: [Analysis – 15 marks]

This question has a number of parts. For solving this question, you need to have a strong grip on the following things. Using the same paper for explanations:(May/June 2018 Paper 5 Variant 2).

Conversion to linear form:

Firstly, you should be comfortable with transforming ANY given equation to linear form (Y = mX + c). Make yourself familiar with the logarithmic rules to help you in this.

In the example paper, the equation given in question 2 is:

physics-p5-1

It can be arranged into linear form like this (t is measured, hence a dependent quantity, and resistance (nR) is varied, hence an independent quantity):

Taking ln on both sides,

physics-p5-2

Using the power rule of logarithm on the right side, we get,

physics-p5-3

Comparing this final equation with linear form (Y=mX + c),

physics-p5-4

This shows that if a graph of ‘t’ against ‘nR’ is plotted, we will obtain a straight line graph passing through the origin (it can then be deduced that ‘t’ is directly proportional to ‘nR’)

Treatment of uncertainties and significant figures:

Secondly, you should be familiar with the treatment of uncertainties and significant figures.

For finding the percentage/absolute/fractional uncertainty, keep in mind the following rules:

  • in case of addition / subtraction:
    • We add the individual uncertainties of the quantities added or subtracted. Take the following example:
      a = 5 ± 0.2 & b = 2 ± 0.3
      We are given, c = a + b
      Find the absolute uncertainty & percentage uncertainty in c.
      c = 5 + 2 = 7
      absolute uncertainty in c = 0.2 + 0.3  = 0.5
      percentage uncertainty in c = 0.5/7 * 100 = 7.14% (up to 3 sf.)

Note: whatever the case (subtraction or addition), the individual uncertainties are always ADDED never subtracted!

  • in case of multiplication / division:
    • We add the fraction uncertainties of the involved quantities. Take the following example:
      a = 2 ± 0.2 & b = 3 ± 0.3
      We are given, c = b/a
      Find the absolute uncertainty & percentage uncertainty in c.c = 3/2 = 1.5
      fractional uncertainty in a = Δa/a = 0.2/2 = 0.1
      fractional uncertainty in b = Δb/b = 0.3/3 = 0.1
      fractional uncertainty in c = (Δa/a + Δb/b) = 0.1 + 0.1 = 0.2
      absolute uncertainty in c =  (Δa/a + Δb/b) * c = (0.1 + 0.1) * 1.5 = 0.3
      percentage uncertainty in c = (Δa/a + Δb/b) * 100 = 0.2 * 100 = 20%
  • in case powers are involved:
    • When powers are involved in the given expressions, we find the uncertainties in the same way as above, with just a small change: we multiply the power with the fractional uncertainty of the value which is raised to that power. For example:
      P = I2R
      when finding the percentage uncertainty of P, we’ll do it like this:
      percentage uncertainty in P = (2 (ΔI/I) + ΔR/R) * 100
      Just see how everything is done exactly the same, except that inclusion of power 2.
  • in case of logarithmic uncertainties:
    • We are given: a = 2 ± 0.2
      log a = log 2 = 0.301
      uncertainty in log = log (2+0.2) – log(2) = 0.0414
      log (2±0.2) = 0.301 ± 0.041

Calculate all the data in 3 significant figures (generally done) or to one s.f. more or equal to the s.f of the raw data.

However, in the case of logarithmic calculations, the number of d.p for the calculated log is the number of s.f in the raw data. Hence for raw data of 3 s.f. the log should be calculated to 3 d.p.

The significant figures of uncertainty are usually ignored in the marking scheme but stick to 1 or 2 s.f.

Graphs:

Thirdly, make sure you know how to draw the graphs for this question.

The general instructions for drawing graphs are:

  • Use small encircled dots or crosses to plot the points.
  • Use a sharp pencil.
  • If a gradient is to be calculated, draw a triangle and mentioning the points of the vertices on the best-fit line. The hypotenuse should be greater than half the length of the best-fit line.

Drawing worst-fit lines:

Once you are done plotting the best-value points, add or subtract the error from the best point, and plot this above or below, or left or right the best-value point, depending on the question.

Join the three points together to form the error bar.

physics-p5-5

The worst-fit line can then either be the shallowest (drawn by joining the bottom of the topmost bar, and top of the bottommost bar) or steepest (drawn by joining the top of the topmost point’s error bar and the bottom of the bottommost error bar) possible line that passes through every error bar.

Draw either the shallowest or steepest worst-fit line, NOT both. Both lines should be clearly labeled.

For calculation of error in gradient, calculate the gradients for both lines by drawing triangles with hypotenuses greater than half the lengths of both lines and mentioning the points of vertices on both the best and worst fit lines. Find error by subtracting the gradient of best-fit from worst-fit. All calculations should be to 3 s.f.

Take special care of units and powers of tens. Don’t forget to mention the units along with answers!

This was all about paper 5 of A Level Physics. We really hope it proves useful.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

44 Comments
Inline Feedbacks
View all comments
floh

When we plot the graph..imagine the smallest one box measures to 0.05 and I am required to plot 8.23. Do I plot it by rounding it to 8.20 or do I make an estimate and draw somewhere in between 8.20 and 8.25? What does cie require?

Nfs

You round off to 8.20 as the number 3 in 8.23 is lesser than 5,if it is greater than or equal to 5 (Eg- 8.25 or 8.27) then it would have been 8.30

Last edited 1 year ago by Nfs
Hashir

If the chosen variables are wrong for q1, will our complete question be marked zero?

Syed Zulnoon Shah

Found it so helpful. Very well explained, thanks.

Makanaka

Thank you so much

Alizay

How do we find uncertainty though, with the difference formula given in ms (eg s19 qp52 Q2)

marcus

When they ask you error for gradient do you need to turn everything into SI units?

Simba

Guys… You save lives thank you for the post… Just wrote maths p3 today and i knew everything but could not do everything because i was slow. I didnt finish the paper.
Dont do that guys. Work fast and accurate.

Tomi

yh I feel you, I had no idea how to do vectors question and only barely learned argand diagram yesterday. I had 20mins extra but had no knowledge to put down. Don’t do this guys, study hard. Praying for your success @simba!

Levi

Hey.. when plotting the error bars..is it error×2 and thank you soo much for this… you’re a life saver

SurvivingP5physics

Hi! when there are power of tens on the axis or something like mm, do we need to include them in the calculation of the gradient? Thanks so much!

Prince Ntsima

This is dope .

Fizza

In Question 2, in the Last 3-4 Parts Right after The Gradient and intercept Part..where They ask you questions related to uncertainties..Will There be E.C.F if I haven’t calculated a value In the correct Units and have used that same value for the next 2-3 parts?

Durian123

Hi can I know for p5 question 2, if you have drawn a wrong graph, will you lose your marks for the subsequent questions that ask for gradient and y intercept? Or is the error carried forward and only the mark for graph is lost?

Student

Is it a must to draw the triangle for determining the gradient?

Shisnsn

Yes it is compulsory,and make sure the hypotenuse is is covering more than half of the graph

Wandi

This is so useful thank you so much!!!!

Tanah

this was really helpful, kudos to you and your team

Hamna

I am having my exam in few hours…It helped ALOT…Thanks

a level student

Also is the worst fit line drawn from the centre of the topmost bar to the centre of the bottom most bar right?

Rizwan

No.it is best if from middle to middle

A Level student

May I know whether I have to write gradient with unit?

metier

You do. It is often written do provide the necessary units.

Anonymous01

thank you so much, very useful!! 🙂

Qaiser Nawaz

This was very useful. Thank you so much!